Double tap to zoom
|All Land Pride Cutters have been designed and tested and meet rigorous voluntary
testing procedures specified by ANSI.
|Factory assembled||Saves customer set-up time and money.|
|Fully welded deck||Fully welded deck adds strength.|
|7 Year gearbox warranty*||Shows confidence in out gearboxes.|
|250 HP Divider gearbox
210 HP center & wing gearboxes
|A rugged heavy built gearboxes capable of handling heavy cutting applications.|
|Gearbox seal protection||Gearbox bottom seal protection for longer bearing life.|
Cat. 6 CV or Cat. 5 Conventional
|Holds up to shock loads and harsh mowing conditions.
Fits wide range of tractors including high horsepower tractors.
|Star profile drivelines||Star profile spreads load out to many points on the shaft. More apt to resist bending and
twisting under shock loads and harsh mowing conditions.
|Easy greasable drivelines||Drivelines have access holes for greasing the U-joints and to grease the inner profiles.|
|4 Plate slip-clutch||Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline
when impacts are encountered.
|High blade tip speed||540 rpm: Center: 17,377 fpm, Wings: 17,329 fpm
1000 rpm: Center: 18,165 fpm, Wings: 15,013 fpm
Allows for a clean cut of material and even distribution.
|6" Blade overlap||Generous blade overlap eliminates skipping, especially in turns.|
|High cutting capacity||Can cut brushy areas with saplings up to 3".|
|Left wing rotates counterclockwise||Better discharge of material. Picks up tractor tracks.|
|10 1/2" Deck height||Handles heavy cutting, which reduces balling-up of cut material under the deck.|
|3/16" Stump jumper backed with a
1" thick mounting bar
|Heavy round stump jumper with bottom gearbox seal protector. Can hold up to tough
|3/16" Deck thickness||Heavy enough to handle conditions but not weigh unit down.|
|Self-leveling pull-type hitch||Reduces drawbar wear by keeping hitch level while going through ditches.|
|LED Signal lights||LED lights are bright, long lasting, and resistant to vibration, unlike incandescent
|Hinged wing sections||Allow cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and
hollows can cause uneven cutting.
|1" Solid hinge rods||Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in
the hinge area itself.
|Wing transport locks||Safety feature. Holds wing sections up in case of hydraulic pressure loss.|
|Enclosed front to rear dual leveling
|Dual leveling rods enable the cutter to pull equally on the rear axle during travel over
rough terrain. Many competitors only use one leveling rod.
|Drain holes in wheel rims||Allows water to drain from wheels mounted on the folded-up wings.
Helps prevent paint deterioration and rusting to the wheel rims.
|5" Square rear axle tubing||Heavy axle to handle harsh conditions.|
|Spring-cushioned center-axle||Protects unit from bumps and ground shock.|
|Replaceable wheel spindles||Wheel spindles can be replaced when damaged without replacing the entire axle.
Simply remove two bolts to replace damaged spindle.
|Double swivel hitch||Great for uneven terrain, reduces drawbar wear.|
|Bar-tite hitch||Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.|
|Wheel options||Laminated tires: Eliminates flats.
Airplane tires without foam filling: Give better cushion while transporting.
Airplane tires with foam filling: Give better cushion while transporting and can’t go
|Deck rings (optional)||1/2" x 3" full welded deck ring keeps blades from damaging the deck.|
|Shredder Blades (Optional)||Ideal for cutting residue into smaller pieces.
Replaces blade and stump jumper configuration.
|Baffles (Accessory)||Maintains shredded material in each section of the cutter for a consistent discharge
from the rear of each deck.
|Specifications & Capacities||RCM5020|
|Min. horsepower||90 power take-off horsepower (67.1 kw)|
|Gearbox horsepower||250 (186.4 kw) Splitter
225 (167.8 kw) Center deck & wing decks
lubrication & capacity
|Center deck & wings: 10 pints (4.73 L) of gear lube 80-90W EP
Divider gearbox: 5.5 pints (2.60 L) of gear lube 80-90W EP
|Cutting capacity||Up to 3" (7.6 cm) material|
|Machine weight||7,340 lbs (3,329.4 kg)|
|Blade tip speed At 540 rpm
At 1000 rpm
|Center blade: 17,377 FPM (88.3 mps) & wing blade: 17,329 FPM (88 mps)
Center blade: 18,165 FPM (92.3 mps) & wing blade: 18,317 FPM (93.1 mps)
|Tongue weight||2,668 lbs (1,210.2 kg)|
|Hitch types||Standard clevis hitch, pintle hitch, ball hitch, LP performance hitch and bar-tite hitch|
|Hitch jack||Standard hand crank|
7 Pin connector
|LED (standard) SAE J560 pin configuration|
Minimum transport width
|20'-0" (6.10 m) 20'-10" (6.35 m) 8'-9" (2.44 m)|
|Overall length||19'-3" (5.87 m)|
|Deck height||10 1/2" (3.06 m)|
|Cutting height*||2" (5.1 cm) to 14" (35.6 cm) with hydraulic cylinder and stroke control spacers|
|Lift hydraulics||4" x 8" Hydraulic cylinder, hoses, fittings & stroke control spacers|
|Wing hydraulics||3 1/2" x 12" Hydraulic cylinders, hoses & fittings|
|Wing transport protection||Wing transport locks|
|Deck sheet thickness||10g (3.4 mm) top and 10g (3.4 mm) bottom|
|Side skirt thickness||1/4" (6 mm)|
|Skid shoes Wing decks
|Replaceable and reversible
|Blades - 6 (2 per carrier)||1/2" (13 mm) x 4" (10.2 cm) Heat-treated, free-swinging alloy steel with uplift|
|Blade overlap||6" (16.2 cm)|
|Blade bolt||Keyed with hardened flat washer & locknut|
|3/16" (5 mm) Round dish shaped bolt-on stump-jumper (optional)
1" (2.5 cm) diamond shaped blade bar
|Deck rings (optional)||1/2" (13 mm) x 3" (7.6 cm) fully welded|
|Front & rear guards||Single chain or double chain|
Input driveline options
|Constant velocity u-joint ASAE Cat. 6 with or without over running clutch|
Intermediate & wing drivelines
|ASAE Cat. 5 with slip-clutch protection|
|Tire & wheel options||6" x 21" Laminated tires
6" x 26" Laminated tires
27" x 7.75" x 15" Used aircraft tires with foam filling
29" Used aircraft tires
|Number of wheel||6 - Wheel option: 4 on transport axle and one on each wing axle
8 - Wheel option: 4 on transport axle and two on each wing axle
|Transport axle||Spring-cushioned on center transport axle or optional walking tandem on center axle|
|Hubs||Cast iron 5-bolt hubs with tapered roller bearings and with 1 3/4" (4.4 cm) shafts|
|Shredder blades (optional)||Cuts material into smaller pieces|
|Baffle Kit (optional)||Front & rear mounted|
|* Maximum cut height is dependent on tire options selected.|
Let us help you get moving
Fields with asterisks* are required. Please email our helpful staff with any questions or comments using the contact form.