Double tap to zoom
|Surpassed rugged industry standards||All Land Pride Rotary Cutters have been designed and tested and meet rigorous
voluntary testing procedures according to ISO 4254-13.
|Factory assembled||Arrives for quick and easy set-up. Minimal time wasted setting or prepping the unit.|
|7 Year gearbox warranty||Shows confidence in gearbox integrity.|
|Rugged heavy built gearboxes||Capable of handling heavy cutting applications.|
|Gearbox seal protection||Gearbox bottom seal protection for longer bearing life.|
|Sliding guard for splitter gearbox||Sliding guard offers protection and easy access for improved efficiency of splitter
|2 Piece driveline shields||Driveline grease zerks are easier to access.|
|Low hitch weight on tractor tongue||Ideal for smaller hp tractors by reducing the amount of weight on the drawbar.|
|Narrow A-frame hitch||Allows for a tighter turning radius.|
|Adjustable park jack angle||Park jack can be adjusted to be perpendicular to the ground.|
|Adjustable driveline hanger||Serves as support rest for the driveline when the cutter is unhooked from the tractor.
Assist operator when attaching driveline to tractor power take-off shaft.
|Input driveline: Cat. 6 CV||Driveline is matched just right for tractor capacity. Constant velocity (CV) U-joint
allows for 80 degree turns without doing damage to the driveline.
|Drivelines with slip-clutches:
Cat. 4 intermediate
Cat. 4 or Cat. 5 wings
Driveline is sized right for the intended cutting capacity.
Slip-clutches will slip under load to minimize twist damage to driveline profiles.
|Grease zerks on end caps of driveline||Intermediate and wing driveline cross journals are easier to grease.|
|High blade tip speed||Allows clean cutting of material.|
|6" Blade overlap||Eliminates skipping during turns.|
|Diamond blade bar||Provides the critical strength needed for consistent, top performance.|
|3/16" Round stump jumper||Standard thick stump jumper material keeps damage to a minimum.|
|Smooth top design||Reduces accumulation of debris and is easier and faster to clean.|
|Tops of decks are 100% welded||Makes center decks and wing decks stronger.|
|1/4" Sidewall thickness||Increased thickness reduces damage from objects being thrown into deck sidewalls.|
|Multiple center skid shoe locations||Run two or four skid shoes in locations under the tongue pivots or out at the wing hinges.|
|Beveled skid shoes on wings||Reduces gouging the ground when turning.|
|LED signal lights||LED lights are bright, long lasting, and resist vibration, unlike incandescent lights.|
|Hinged wing sections||Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and
hollows can cause uneven cutting.
|1" Solid hinge rods||Larger diameter hinge rod provides greater strength in the hinge area.|
|Wing transport lock pins||Transport lock pins will hold wings in folded position in the event of hydraulic loss.|
|Enclosed dual 1" leveling rods||Cutter pulls equally on the rear axle while traveling over rough terrain.|
|5-Bolt hubs||5-Bolt hubs makes the wheel assembly more durable and longer lasting.|
|Drain holes in wheel rims||Allows water to drain from wheels mounted on folded-up wings.
Helps prevent paint deterioration and rusting to the wheel rims.
|Spring cushioned center-axle||Protects unit from bumps and ground shock.|
|Optional spring cushioned wing-axles||Further improves ride over a multitude of terrains.|
|Replaceable individual wheel spindles||Spindles can be replaced when damaged without replacing entire axle assembly.|
|Wheel options||Laminated tires: Eliminates flats.
Air-filled tires: Give better cushion while transporting.
Foam-filled tires: Give better cushion while transporting and can’t go flat.
|LP Performance hitch option||Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and
pivots about the tractor drawbar up to 12 degrees in both left and right directions.
|Bar-tite hitch option||Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.|
|Specifications & Capacities||RC(M)4715 & RCG(M)4715|
|Horsepower range||50 - 250 hp (37.3 - 186.4 kW)|
|Gearbox horsepower||540 rpm or 1000 rpm
250hp (186.4 kW) Divider and 210hp (156.6 kW) Center & Wings
|Gearbox lubrication||Gear Lube 80-90W EP|
|Gearbox oil capacity||Splitter: 3.5 pints (1.66 L); Center deck & Wings: 6 pints (2.84 L)|
|Cutting capacity||4" (10.2 cm)|
|Machine weight Total weight
|5,000 lbs. (2268 kg)
1860 lbs. (843.7 kg)
|Blade tip speed At 540 rpm
At 1000 rpm
|Center Blades & Wing Blades = 16,300 FPM (82.8 mps)
Center Blades = 16,300 FPM (82.8 mps) & Wing Blades = 16,000 FPM (81.3 mps)
|Hitch types||Swivel Clevis Hitch, LP Performance Hitch, Bar-Tite Hitch, Ball Hitch, or Pintle Hitch.|
|Hitch jack||Standard (7,000 lbs.) (3175.1 kg)|
7 Pin connector
SAE J560 pin configuration
Transport width with 21" tires
|15'-0" (4.57 m)
15'-10" (4.83 m)
10'-3" (3.12 m) - Single-acting fold option, 7’-3" (2.21 m) - Dual-acting fold option.
|Overall length||16'-3" (4.95 m) - With center deck raised fully up.|
|Deck height||12" (30.5 cm)|
|Cutting height||1-1/2" - 16" (3.8 cm - 40.6 cm) - Varies by tire option.|
|Lift hydraulics||3" x 8" (7.6 cm x 20.3 cm) hydraulic cylinder, hoses, fittings & stroke control spacers.|
|Wing hydraulics||2 1/2" x 12" (6.4 cm - 30.5 cm) hydraulic cylinders, hoses & fittings.|
|Wing transport protection||Wing Transport Lock Pins|
|Deck material thickness||10 Gauge (3.4 mm)|
|Side skirt thickness||1/4" (6 mm) Steel|
|Skid shoes||Wing Deck: 1 Replaceable skid shoe per wing.
Center Deck: 2 Replaceable skid shoes and multiple mounting locations.
|Blades - 6 (2 per carrier)||1/2" x 4" (1.3 cm - 10.2 cm) Heat-treated, free-swinging alloy steel with uplift.|
|Blade overlap||6" (15.2 cm)|
|Blade bolt||Keyed with hardened flat washer & locknut.|
|Stump jumper / blade holder||3/16" (5 mm) Thick round dish shaped pan, reinforced with 1" x 4" (2.5 x 10.2 cm) blade bar.|
|Front & rear guards||Optional single row chain or dual row chain.|
|Input driveline 540 & 1000 rpm||Cat. 6 with constant velocity u-joint with or without overrunning clutch.|
|Intermediate driveline||Standard - Category 4 with slip-clutch.|
|Wing drivelines||Standard - Category 4 with slip-clutch or Category 5 with slip-clutch.|
|Wheel options||21" (53.3 cm) or 26" (66 cm) Laminated tires
24" (61 cm) Used aircraft, foam filled tires
25.5" (64.8 cm) 20 ply tires, foam filled or pneumatic
29" (73.7 cm) Used aircraft tires
|Number of wheels||6 - Wheel option: Four on transport axle and one on each wing axle.
8 - Wheel option: Four on transport axle and two on each wing axle.
|Transport axle||Many configurations to choose from.|
|Hubs||Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" (4.4 cm) shafts.|
|LP Performance hitch & Bar tite hitch pivot shaft diameter||2 1/4" (5.7 cm)|
|A-frame tongue||5" x 3" (12.7 cm x 7.6 cm) rectangular tubing|
Let us help you get moving
Fields with asterisks* are required. Please email our helpful staff with any questions or comments using the contact form.